Shield/Module

OVERVIEW:The 2.4″ Colour TFT display with micro SD card slot is now available as a SHIELD for Arduino UNO.It has a four-wire resistive touch screen, a micro SD card socket, a reset switch and a convenient Arduino Uno shield footprint. Specification:2.4 inch LCD TFT display has Bright, 4 whi..

OVERVIEW:Compatible with Arduino Mega pinoutReset button up topICSP headerLots of GND and +5V railsDIP prototyping area makes it easy to add more chipsSOIC prototyping area above USB jack for up to 14-pin SOIC chip, narrow medium or wide package.Use 'mini' or 'medium' breadboardTwo 3mm LEDs with mat..

OVERVIEW:The GPS Shield is based on ublox’s NEO-6M GPS receiver module. The Shield is pin compatible for Arduino UNO, Mega, Leonardo and Arduino Due boards. The GPS pins RX,TX can be configured to make connections with D0-D7 pins on Arduino using on board configureable jumper for RX and TX routing. ..

OVERVIEW:Arduino GPS shield is a GPS module breakout board designed for Global Positioning System receiver with SD interface. It is easy to use for recording the position data into the SD card. 5V/3.3V compatible operation voltage level makes it compatible with Arduino boards, leaf maple, IF..

OVERVIEW:The GPS module with NEO-6M U-Blox chip and the external ceramic antenna can be controlled via UART with Arduino and Raspberry Pi after which the position can be retrieved. An LED on the module shows if there is an active connection to a GPS satellite.The module can also be connect..

OVERVIEW:The NEO-6 module series brings the high performance of the u-blox6 position engine to the miniature NEO form factor. U-blox6 has been designed with low power consumption in mind. Intelligent power management is a breakthrough for low-power applications. All NEO-6 modules are manufactured in..

OVERVIEW:A motor driver is an integrated circuit chip which is usually used to control motors in autonomous robots. Motor driver act as an interface between Arduino and the motors . The most commonly used motor driver IC’s are from the L293 series such as L293D, L293NE, etc. These ICs are designed t..

OVERVIEW:MINI L293D is a monolithic integrated, high voltage, high current, 4-channel driver. With this chip you can control DC motors and power supplies of up to 25 Volts.  The L293D chip is also known as H-Bridge. The H-Bridge is typically an electrical circuit that enables a voltage to be ap..

OVERVIEW:The Arduino Ethernet Shield connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino board, connect it to your network with an RJ45 cable (not included) and follow a few simple instructions to start controlling your world through the internet. A..

OVERVIEW:The Arduino WiFi Shield connects your Arduino to the internet wirelessly. Connect it to your wireless network by following a few simple instructions to start controlling your world through the internet. As always with Arduino, every element of the platform – hardware, software and d..

OVERVIEW:The Xbee shield allows an Arduino board to communicate wirelessly using Zigbee. It is based on the Xbee module from MaxStream. The module can communicate up to 100 feet indoors or 300 feet outdoors (with line-of-sight). It can be used as a serial/USB replacement or you can put it in..

OVERVIEW:The Relay Shield provides a solution for controlling high current devices that cannot be controlled by the Arduino’s Digital I/O pins due to their current and voltage limits.The Relay Shield features four high quality relays and provides NO/NC interfaces, four dynamic LED indicat..

OVERVIEW:Sensor Shield allows you to connect to various modules like sensors, servos, relays, buttons, potentiometers, Each functional module has buckled port with VCC, GND, and Output, which has corresponding port on the Sensor Shield, connected with a plain 2.54mm dual-female cable you may..

OVERVIEW:The Relay Shield provides a solution for controlling high current devices that cannot be controlled by the Arduino’s Digital I/O pins due to their current and voltage limits.The Relay Shield features four high quality relays and provides NO/NC interfaces, four dynamic LED indicators to s..

OVERVIEW:This expansion board as a driver expansion board can be used for engraving machines, 3D printers. It has a total of four slots, can drive four A4988 stepper motor. The A4988 is a complete micro-stepping motor driver with built-in translator for easy operation. It is designed to oper..

OVERVIEW:The Relay Module provides a solution for controlling high current devices that cannot be controlled by the Arduino’s Digital I/O pins due to their current and voltage limits.The Relay Module features four high quality relays and provides NO/NC interfaces, four dynamic LED indicat..

OVERVIEW:Onboard 5v->3v regulator provides 150mA for power-hungry cards.3v level shifting means you can use this with ease on either 3v or 5v systems.Uses a proper level shifting chip, not resistors: less problems and faster read/write access.Use 3 or 4 ..

FEATURES:5V 16-Channel Relay interface board, and each one needs 50-60mA driver currentEquipped with high-current relay, AC250V 10A; DC30V 10AStandard interface that can be controlled directly by microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)I..

OVERVIEW:OV7670 image sensor, small volume, low operating voltage, providing all functions of a single chip of VGA camera and image processor. Through SCCB bus control, the sensor can output the whole frame, sampling, and various resolution 8 bits of data. The product VGA image can reach up..

FEATURES:4 X 2.6 X 3.2CM2 potentiometers for 2 axes1 switchConnector: +5Vcc - GND - VRx - VRy - SWHigh-Quality Atomic MarketDocument:Arduino Joystick Module..

OVERVIEW:This little shield that could, takes the small and feisty NANO and gives it all the capabilities of its bigger brother, the UNO.The shield gives you full access to all the digital and analogue ports that an Arduino NANO can possibly provide and gives each its own VCC and GND. Th..

OVERVIEW:The Relay Module provides a solution for controlling high current devices that cannot be controlled by the Arduino’s Digital I/O pins due to their current and voltage limits.The Relay Shield features four high quality relays and provides NO/NC interfaces, four dynamic LED indicators to show..

OVERVIEW:This is a 30V DC Voltmeter that operates over a wide voltage range of input voltage (from 3 to 30V). Only two wires are needed to interface this device with the target circuit and the same DC voltage is used for powering the meter from the target circuit.The PCB assembly has two ..

OVERVIEW:The module is fully considered mine design, long-distance transmission signal 485 in the wild, the module "Connected to the ground" terminal is connected to the earth, can play a very good anti-jamming and anti-lightning effect, more secure; it can not connect with the ground when the indoo..

OVERVIEW:The Arduino USB Host Shield allows you to connect a USB device to your Arduino board. The Arduino USB Host Shield is based on the MAX3421E (datasheet), which is a USB peripheral/host controller containing the digital logic and analog circuitry necessary to implement a full-speed USB..